YOUR PLUMBING CRASH COURSE: A GUIDE TO INSTALLING A BATHTUB

Your Plumbing Crash Course: A Guide to Installing a Bathtub

Your Plumbing Crash Course: A Guide to Installing a Bathtub

Blog Article

Click Here

What are your ideas on Installing A Bathtub?


A Step-by-Step Guide to Installing a Bathtub
Mounting a tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard project. If the old bathtub is readily available, the job can move quickly; if you have to open a wall surface to get rid of the old bathtub and place the brand-new bath tub, the job is much harder. In either case, the task is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the work and fit attempting it. As opposed to hiring a contractor to take over a halfway-completed task, it is far better to think about utilizing one prior to you begin. Opportunities are you may need a specialist plumber to make tube links.
This write-up will assist you mount a new tub in your bathroom if you have currently gotten a brand-new bathtub as well as do not need to alter the setup of your previous water supply pipes.
Your tools and material checklist need to consist of the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installation


    Firstly, the sustaining framework supplied with the bath must be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to prevent strain on the bath tub.
    Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
    Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last position.

    Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be fairly problematic due to the limited accessibility that is often the case.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. Once the supply pipes have been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
    Before carrying on to fit the new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.

    Setting up the Tub


    Utilizing both wooden boards under its feet, put the bathtub in the called for setting. The wood boards are practical in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
    The following objective is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bathtub up until the spirit level reads level.
    To install faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the various other tap.
    Switch on the supply of water and inspect all joints and new pipework for leaks and also tighten them if necessary. Load the bathtub as well as additionally check the overflow electrical outlet and the normal outlet for leakages.
    Ultimately, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub must wait till the bath tub has been used a minimum of once as this will settle it into its last position.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipes.
    If you need to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next, position the faucet in the installing opening in the bath/basin making certain that the washers remain in area between the tap as well as the sink. Safeguard the tap in position with the producer provided backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind ought to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the location where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall between the bathroom and the tiling, resulting in problems with wetness and also feasible leakages to the ceiling listed below.
    You can select from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can crack fairly early if you do not take into consideration this activity prior to securing.
    Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    Do you appreciate reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Make feedback down below. We will be glad to listen to your opinion about this page. In hopes that you visit us again in the future. Do you know somebody who is involved in the subject? Take a moment to share it. I praise you for your time. Please pay a visit to our blog back soon.


    Service excellence here.

    Report this page